r07ds0258ej0100 rev.1.00 page 1 of 6 mar 30, 2011 preliminary datasheet BCR08DS-14A triac low power use features ? i t (rms) : 0.8 a ? v drm :700 v ? i fgti , i rgti , i rgtiii : 5 ma ? planar passivation type ? surface mounted type ? completed pb free outline renesas package code: prsp0004za-a (package name: sot-223) 4 1 2 3 2, 4 1 3 1. t 1 terminal 2. t 2 terminal 3. gate terminal 4. t 2 terminal applications washing machine, electric fan, air cleaner, other general purpose control applications maximum ratings voltage class parameter symbol 14 unit repetitive peak off-state voltage note1 v drm 700 v non- repetitive peak off-state voltage note1 v dsm 840 v notes: 1. gate open. parameter symbol ratings unit conditions rms on-state current i t (rms) 0.8 a commercial frequency, sine full wave 360 conduction, tc= 96c note3 surge on-state current i tsm 8 a 60hz sinewave 1 full cycle, peak value, non-repetitive i 2 t for fusing i 2 t 0.26 a 2 s value corresponding to 1 cycle of half wave 60hz, surge on-state current peak gate power dissipation p gm 1 w average gate power dissipation p g (av) 0.1 w peak gate voltage v gm 6 v peak gate current i gm 0.5 a junction temperature tj ?40 to +125 c storage temperature tstg ?40 to +125 c mass ? 0.12 g typical value r07ds0258ej0100 rev.1.00 mar 30, 2011
BCR08DS-14A preliminary r07ds0258ej0100 rev.1.00 page 2 of 6 mar 30, 2011 electrical characteristics parameter symbol min. typ. max. unit test conditions repetitive peak off-state current i drm ? ? 1.0 ma tj = 125c, v drm applied on-state voltage v tm ? ? 2.0 v tc = 25c, i tm = 1.2 a, instantaneous measurement ? v fgt ? ? ? 2.0 v ?? v rgt ? ? ? 2.0 v gate trigger voltage note2 ??? v rgt ??? ? ? 2.0 v tj = 25c, v d = 6 v, r l = 6 ? , r g = 330 ? ? i fgt ? ? ? 5 ma ?? i rgt ? ? ? 5 ma gate trigger current note2 ??? i rgt ??? ? ? 5 ma tj = 25c, v d = 6 v, r l = 6 ? , r g = 330 ? gate non-trigger voltage v gd 0.2 ? ? v tj = 125c, v d = 1/2 v drm thermal resistance r th (j-c) ? ? 25 c/w junction to case note3 critical-rate of rise of off-state commutating voltage note4 (dv/dt)c 0.5 ? ? v/ ? s tj = 125c notes: 2. measurement usi ng the gate trigger characteristics measurement circuit. 3. case temperature is measured on the t2 tab.. 4. test conditions of the critical-rate of rise of off-state commutating voltage is shown in the table below. test conditions commutating voltage and current waveforms (inductive load) 1. junction temperature tj = 125c 2. rate of decay of on-state commutating current (di/dt)c = ?0.4 a/ms 3. peak off-state voltage v d = 400 v supply voltage time time time main current main voltage (di/dt)c v d (dv/dt)c
BCR08DS-14A preliminary r07ds0258ej0100 rev.1.00 page 3 of 6 mar 30, 2011 performance curves 10 3 10 2 10 1 ?40 0 40 80 120 160 maximum on-state characteristics on-state voltage (v) on-state current (a) rated surge on-state current conduction time (cycles at 60hz) surge on-state current (a) gate characteristics gate current (ma) gate voltage (v) gate trigger voltage vs. junction temperature junction temperature (c) gate trigger voltage (tj = tc) gate trigger voltage (tj = 25c) 100 (%) gate trigger current vs. junction temperature junction temperature (c) gate trigger current (tj = tc) gate trigger current (tj = 25c) 100 (%) maximum transient thermal impedance characteristics (junction to case) conduction time (cycles at 60hz) transient thermal impedance (c/w) 4.0 1.5 2.5 3.5 1.0 2.0 3.0 10 1 10 0 10 ?1 10 0 2 6 8 4 10 0 10 1 10 2 10 3 10 2 10 1 ?40 0 40 80 120 160 typical example typical example 10 1 10 0 10 ?1 10 1 10 2 10 1 10 0 10 ?1 10 3 10 4 10 2 10 2 10 3 p gm = 1w i gm = 0.5a v gm = 6v v gt = 2v i fgt i , i rgt i , i rgt iii 0 5 15 20 25 30 tj = 25c v gd = 0.2v p g(av) = 0.1w 10
BCR08DS-14A preliminary r07ds0258ej0100 rev.1.00 page 4 of 6 mar 30, 2011 on-state power dissipation (w) rms on-state current (a) maximum on-state power dissipation rms on-state current (a) case temperature (c) allowable case temperature vs. rms on-state current junction temperature (c) repetitive peak off-state current (tj = tc) repetitive peak off-state current (tj = 25c) 100 (%) repetitive peak off-state current vs. junction temperature holding current vs. junction temperature junction temperature (c) holding current (tj = tc) holding current (tj = 25c) 100 (%) 0 0.4 1.2 1.6 2.0 0.8 0 0.2 0.4 0.8 1.2 0.6 1.0 1.4 10 3 10 2 10 1 ?40 0 40 80 120 160 ?40 0 40 80 120 160 10 2 10 5 10 4 10 3 0 0.2 0.4 0.6 0.8 1.0 0 20 40 80 60 100 120 140 160 typical example typical example breakover voltage vs. junction temperature junction temperature (c) breakover voltage (tj = tc) breakover voltage (tj = 25c) 100 (%) latching current (ma) latching current vs. junction temperature junction temperature (c) 0 20 40 80 60 100 120 140 160 ?40 0 40 80 120 160 ?40 0 40 80 120 160 t 2 + , g ? typical example t 2 + , g + typical example distribution typical example 10 2 10 0 10 1 10 ?1 t 2 ? , g ? typical example 360 conduction resistive, inductive loads 360 conduction resistive, inductive loads curves apply regardless of conduction angle
BCR08DS-14A preliminary r07ds0258ej0100 rev.1.00 page 5 of 6 mar 30, 2011 rate of rise of off-state voltage (v/ s) breakover voltage (dv/dt = xv/ s) breakover voltage (dv/dt = 1v/ s) 100 (%) breakover voltage vs. rate of rise of off-state voltage 10 1 10 2 10 0 10 3 0 20 40 80 60 100 120 160 140 typical example tj = 125c commutation characteristics (tj=125c) critical rate of rise of off-state commutating voltage (v/ s) rate of decay of on-state commutating current (a/ms) 10 0 10 ?1 10 1 10 ?1 10 0 10 1 10 1 10 0 10 2 gate trigger current vs. gate current pulse width gate current pulse width (s) gate trigger current (tw) gate trigger current (dc) 100 (%) 10 3 10 2 10 1 typical example 6 6 6 6v 6v 6v r g r g r g a v a v a v test procedure i test procedure iii test procedure ii gate trigger characteristics test circuits conditions v d = 200v i t = 1a = 500s tj = 125c typical example i quadrant iii quadrant minimum characteristics value i quadrant iii quadrant i rgt iii i fgt i i rgt i
BCR08DS-14A preliminary r07ds0258ej0100 rev.1.00 page 6 of 6 mar 30, 2011 package dimension 6.6 0.1 7.0 0.3 1.0 0.2 3.5 0.2 1.75 1.75 3.0 0.1 0.33 0.1 0.33 0.1 0.05 0.05 1.8 max. 0.74 0.1 2.3 0.1 unit: mm ? 0.12 g m ass[t y p. ] ? pr s p 000 4za- a r ene s a s code jeita packa g e cod e pr e vi ous code packa g e nam e so t-22 3 0.1 ordering information orderable part number packing quantity remark BCR08DS-14A-t13#b10 embossed tape 3000 pcs. taping direction ?t1? note : please confirm the specificat ion about the shipping in detail.
notice 1. all information included in this document is current as of the date this document is issued. such information, however, is subject to change without any prior notice. before purchasing or using any renesas electronics products listed herein, please confirm the latest product information with a renesas electronics sales office. also, please pay regular and careful attention to additional and different information to be disclosed by renesas electronics such as that disclosed through our website. 2. renesas electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of renesas electronics products or technical information described in this document. no license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of renesas electronics or others. 3. you should not alter, modify, copy, or otherwise misappropriate any renesas electronics product, whether in whole or in part . 4. descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. you are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. renesas electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. when exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. you should not use renesas electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. renesas electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. renesas electronics has used reasonable care in preparing the information included in this document, but renesas electronics does not warrant that such information is error free. renesas electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 7. renesas electronics products are classified according to the following three quality grades: "standard", "high quality", and "specific". the recommended applications for each renesas electronics product depends on the product's quality grade, as indicated below. you must check the quality grade of each renesas electronics product before using it in a particular application. you may not use any renesas electronics product for any application categorized as "specific" without the prior written consent of renesas electronics. further, you may not use any renesas electronics product for any application for which it is not intended without the prior written consent of renesas electronics. renesas electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any renesas electronics product for an application categorized as "specific" or for which the product is not intended where you have failed to obtain the prior written consent of renesas electronics. the quality grade of each renesas electronics product is "standard" unless otherwise expressly specified in a renesas electronics data sheets or data books, etc. "standard": computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "high quality": transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "specific": aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. you should use the renesas electronics products described in this document within the range specified by renesas electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. renesas electronics shall have no liability for malfunctions or damages arising out of the use of renesas electronics products beyond such specified ranges. 9. although renesas electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. further, renesas electronics products are not subject to radiation resistance design. please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a renesas electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. please contact a renesas electronics sales office for details as to environmental matters such as the environmental compatibility of each renesas electronics product. please use renesas electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the eu rohs directive. renesas electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. this document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of renesas electronics. 12. please contact a renesas electronics sales office if you have any questions regarding the information contained in this document or renesas electronics products, or if you have any other inquiries. (note 1) "renesas electronics" as used in this document means renesas electronics corporation and also includes its majority-owned subsidiaries. (note 2) "renesas electronics product(s)" means any product developed or manufactured by or for renesas electronics. http://www.renesas.com refer to "http://www.renesas.com/" for the latest and detailed information. renesas electronics america inc. 2880 scott boulevard santa clara, ca 95050-2554, u.s.a. tel: +1-408-588-6000, fax: +1-408-588-6130 renesas electronics canada limited 1101 nicholson road, newmarket, ontario l3y 9c3, canada tel: +1-905-898-5441, fax: +1-905-898-3220 renesas electronics europe limited dukes meadow, millboard road, bourne end, buckinghamshire, sl8 5fh, u.k tel: +44-1628-585-100, fax: +44-1628-585-900 renesas electronics europe gmbh arcadiastrasse 10, 40472 dsseldorf, germany tel: +49-211-65030, fax: +49-211-6503-1327 renesas electronics (china) co., ltd. 7th floor, quantum plaza, no.27 zhichunlu haidian district, beijing 100083, p.r.china tel: +86-10-8235-1155, fax: +86-10-8235-7679 renesas electronics (shanghai) co., ltd. unit 204, 205, azia center, no.1233 lujiazui ring rd., pudong district, shanghai 200120, china tel: +86-21-5877-1818, fax: +86-21-6887-7858 / -7898 renesas electronics hong kong limited unit 1601-1613, 16/f., tower 2, grand century place, 193 prince edward road west, mongkok, kowloon, hong kong tel: +852-2886-9318, fax: +852 2886-9022/9044 renesas electronics taiwan co., ltd. 13f, no. 363, fu shing north road, taipei, taiwan tel: +886-2-8175-9600, fax: +886 2-8175-9670 renesas electronics singapore pte. ltd. 1 harbourfront avenue, #06-10, keppel bay tower, singapore 098632 tel: +65-6213-0200, fax: +65-6278-8001 renesas electronics malaysia sdn.bhd. unit 906, block b, menara amcorp, amcorp trade centre, no. 18, jln persiaran barat, 46050 petaling jaya, selangor darul ehsan, malaysia tel: +60-3-7955-9390, fax: +60-3-7955-9510 renesas electronics korea co., ltd. 11f., samik lavied' or bldg., 720-2 yeoksam-dong, kangnam-ku, seoul 135-080, korea tel: +82-2-558-3737, fax: +82-2-558-5141 sales offices ? 2011 renesas electronics corporation. all rights reserved. colophon 1.1
|
